How To Paint Furniture With Vinyl Coated Particle Board

Download Commodity

Download Article

Particle board, or chipboard, is a very lightweight type of wood that's frequently institute in inexpensive furniture or small decorations. Although it is still wood, it'south a lot softer and easier to impairment than regular lumber, making it more than likely to become scratched and more than difficult to paint. If you want to pigment some particle board, sand information technology downwards lightly, apply a sparse layer of primer, and cover it with several coats of pigment to get the look you're later.

1
Remove any hardware or accessories you don't want to pigment over. If you lot're painting particle board article of furniture or touching up cabinets, there may exist metal fittings or handles that you want to keep unpainted. Utilize a screwdriver to carefully remove any hardware, fittings, or accessories attached to the particle lath that y'all don't want to be painted.^[one]
- If you're painting particle board article of furniture, it might exist easier to disassemble it and paint each piece individually. If you can, follow the assembly instructions in reverse to carefully take apart the item yous want to paint.
- Make sure that you store all of the fittings, hardware, screws, and anything else you have out of the particle lath somewhere where it won't get lost.
2
Sand the lath down with 120-dust sandpaper. The lamination or sheen on the particle board will prevent paint from sticking to it. Apply a medium to fine grit sandpaper, around 120-dust, to sand down the confront of the particle lath you want to paint. Sand it down lightly, only plenty to remove the smooth from information technology and expose the wood.^[2]
- Particle lath is a very soft wood, which makes it easier to work with and move around, but also easier to scratch and damage. Use but light pressure level when sanding to avoid dissentious your particle board.
- Employ a vacuum cleaner or shop-vac to remove any dust that comes off the lath while sanding information technology.
- To avoid getting the within of your dwelling messy, sand, prime, and paint your particle board exterior.
Advertisement
three
Glaze the particle board with a layer of oil-based primer. The nearly difficult part of painting particle lath is getting the pigment to adhere to the surface. One time the board has been sanded down, use a broad paintbrush to cover it with a single layer of oil-based primer. Make certain to get into whatsoever hard to reach areas so that the entire surface is covered.^[3]
- A water-based primer volition seep into the particle board and crusade it to not bad up. Always use an oil-based or solvent-based primer when painting particle boards.
- Oil-based primer should be bachelor at your local hardware store. If you're unsure which type to use, ask an employee for assistance choosing the correct primer and pigment for you.
iv
Give the primer 30 minutes to an hour to fully dry. Your coat of primer needs to be completely dry earlier you can begin painting the wood. Leave the particle board sitting out in the sun for 30 minutes to an 60 minutes to give information technology plenty of time to completely dry out.^[4]
- Check the manufacturer's instructions for your called primer for more specific advice on how long information technology will accept to dry.
- You can check if the primer is fully dry out by scratching at information technology lightly with a fingernail. If the primer is dry, a fingernail scratch won't leave a mark or remove any primer.^[5]
Ad

ane
Cover the board with a coat of oil-based pigment. Once the particle lath has been primed, y'all can begin coating it with your paint of choice. Dip a wide-bristled paintbrush or a pigment roller into an oil-based pigment in your desired color. Work slowly and methodically to cover the entire surface with a glaze of pigment.^[6]
- If you have a paint sprayer, you could also use this to evenly paint the particle lath. Work in thin layers to make sure the paint is applied evenly and dries chop-chop.
- Oil or lacquer-based paints will work best for painting particle boards. However, if you have primed the wood with an oil-based primer, you should be able to use water-based paint without the particle lath absorbing any water.
- A diversity of different colored paints should exist available at your local hardware store. Choose one that you lot like and that will work well with the other colors in the room where you'll put your finished particle board.
ii
Let the paint dry for 30 minutes to an 60 minutes. In one case you've finished the beginning glaze of paint on your particle board, leave it to dry out. Give your paint around an hour in the sun to brainstorm to dry. If yous can touch the paint lightly without getting any paint on your finger, the pigment should be dry plenty to apply a second coat.^[vii]
- If you live in a colder or more boiling environment, it may take longer for your paint to dry out. Information technology's meliorate to give it more than time than it needs to dry than it is to move on while the pigment is notwithstanding wet.
- Consult the manufacturer's instructions on your chosen pigment for more specific advice on how long it will take to dry.
iii
Employ some other coat of paint and let it dry. When the paint is dry to the touch, apply a 2nd layer of paint using the same castor or roller. Exit the paint to dry for another 30 minutes to an hr. Repeat this process until y'all are happy with the look of your particle board.^[8]
- With nigh particle board, it will have between two and iv layers of paint to completely cover the primer.
4
Reassemble and reattach the hardware. With your particle board painted and dry to the bear upon, you tin can begin putting it back together. Reassemble the particle board if y'all disassembled it to paint it, and reattach whatever hardware or fittings until everything is put back together.^[nine]
- The paint may all the same exist soft when you begin reassembling your particle board, and then make certain you lot work carefully. Alternately, you tin can leave your particle lath to dry for 12 to 24 hours before reassembling information technology.
Ad

Add New Question

Question

Practise yous demand to sand particle board earlier painting?

Crystal Chadwick is a Licensed General Contractor and the Owner of Yin & Yang Construction out of Salt Lake City, Utah. With over 16 years of experience in the construction industry, she specializes in remodels, repairs, and handyman services. Crystal leads her team with vision and a detail-oriented approach, assuasive them to provide quality work and pattern to their clients.

Licensed General Contractor

Practiced Answer

Aye, this is a proficient thought. Particle lath is a pretty rough material, so take some time to sand whatsoever rough edges before you get started.
Question

Can I utilize two-in-one primer and paint instead of priming separately?

Crystal Chadwick is a Licensed General Contractor and the Owner of Yin & Yang Construction out of Salt Lake Metropolis, Utah. With over 16 years of feel in the structure industry, she specializes in remodels, repairs, and handyman services. Crystal leads her squad with vision and a detail-oriented approach, allowing them to provide quality piece of work and design to their clients.

Licensed General Contractor

Good Answer

You could, but I wouldn't recommend information technology. You'll get better results if you lot prime commencement, then use two coats of pigment after that.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Most paint will take at least a week to completely dry and cure. If you are painting particle board furniture, avert putting anything heavy on it for at least 1 week then as to not run a risk damaging the paint.
You could also paint particle boards with several thin layers of spray paint. Make sure you do so in a well-ventilated area to avert inhaling any overspray.
If you notice the pigment or primer bubbling or spotting as it dries, information technology may be a sign that you didn't sand down that area well enough. Wait for the section to dry, sand information technology downward further, and reapply the primer or paint.

Piece of work exterior or in a well-ventilated area when painting and sanding. This will keep the inside of your home clean and free of stiff paint fumes.